|
|
Engine data | Description | | | | |
|---|
| Engine code | XUJA | XUJB | XVJC | XVJB | | Emission level | Stage 6 | Stage 6 | Stage 6 | Stage 6 | | Firing order | 1-3-4-2 | 1-3-4-2 | 1-3-4-2 | 1-3-4-2 | | Bore | 73.5 mm | 73.5 mm | 73.5 mm | 73.5 mm | | Stroke | 88.3 mm | 88.3 mm | 88.3 mm | 88.3 mm | | Engine capacity | 1,499 cm³ | 1,499 cm³ | 1,499 cm³ | 1,499 cm³ | | Compression ratio | 16:1 | 16:1 | 16:1 | 16:1 | | Power output | 55 kW | 55 kW | 70 kW | 70 kW | | Torque | 190 Nm | 190 Nm | 215 Nm | 215 Nm | | Idle speed | 750 rpm | 750 rpm | 750 rpm | 750 rpm | | Maximum oil consumption | 0.1 l / 1000 km | 0.1 l / 1000 km | 0.1 l / 1000 km | 0.1 l / 1000 km |
Engine oil Oil pressure | Description | Unit |
|---|
| Oil pressure at idle speed | 1–2 bar | | Minimum oil pressure at an oil temperature of 80°C and an engine speed of 2000 rpm | 2.3–3.7 bar |
Engine oil capacity | Description | Unit |
|---|
| Initial fill including oil filter | 4.25 L | | Service fill including oil filter | 3.85 L | | Service fill without oil filter | 3.45 L |
Valve clearances | Description | Unit |
|---|
| Valve clearance (engine cold), intake | 0.103–0.118 mm | | Valve clearance (engine cold), exhaust | 0.113–0.128 mm |
Cylinder Head | Description | Unit |
|---|
| Thickness of cylinder head gasket with piston protrusion of 0.533 - 0.634 | 1.25 (two notches) | | Thickness of cylinder head gasket with piston protrusion of 0.634 - 0.684 | 1.30 (three notches) | | Thickness of cylinder head gasket with piston protrusion of 0.684 - 0.734 | 1.35 (one notch) | | Thickness of cylinder head gasket with piston protrusion of 0.734 - 0.784 | 1.40 (four notches) | | Thickness of cylinder head gasket with piston protrusion of 0.784 - 0.886 | 1.45 (five notches) | | Maximum distortion - measured longitudinally and diagonally | NaN mm |
Camshaft Dimensions | Description | Unit |
|---|
| Camshaft end float | 0.195–0.3 mm | | Camshaft bearing journal diameter | 23.959–23.98 mm |
Crankshaft Dimensions | Description | Unit |
|---|
| Main bearing journal end float | 0.1–0.3 mm | | Main bearing journal diameter | 49.962–49.981 mm |
Cylinder Block | Description | Unit |
|---|
| Cylinder bore diameter | 73.5–73.518 mm | | Main bearing parent bore diameter | 49.98 mm | | Main bearing clearance - radial | 0.017–0.043 mm |
Piston Dimensions | Description | Unit |
|---|
| Piston diameter | 73.4–73.418 mm | | Piston clearance in cylinder | 0.164–0.196 mm | | - upper compression ring | 0.2–0.35 mm | | - lower compression ring | 0.2–0.4 mm | | - oil control ring | 0.2–0.4 mm |
Piston ring gap position: The piston ring gaps must be distributed evenly around the circumference of the piston. This also applies to the oil control ring elements. Align the piston ring gaps at 120 degrees to each other.
Piston Pin Dimensions | Description | Unit |
|---|
| Piston pin length | 59.7–60 mm | | Piston pin diameter | 24.995–25 mm |
Lubricants, Fluids, Sealers and Adhesives | Item | Specification |
|---|
| Sealant, oil pan contact surface to oil seal carrier, oil pan to cylinder block, oil pan to oil pump |
| | Coolant |
|
|
|